Basic Function	Specification
Maximum output frequency	0~500Hz
Carrier frequency	0.5kHz~16.0kHz;According to the load characteristics, carrier frequency can be adjusted automatically
Input frequency	Range :47~63Hz
Control mode	V/F Open/closed loop vector control(SVC/FVC)
Speed range	1:50(Vector mode 0 ) 1Hz/150% rated torque
Overload capability	G type:150% rated current for 60s; 180% rated current for 3s P type:120% rated current for 60s; 150% rated current for 3s
Torque boost	Auto Torque boost Manual Torque boost; 0.1%~30.0%.
V/F curve V/F	Four modes : Line , Multi-point , Square V/F curve, V/F separation
Jog control	Jog frequency range:0.00Hz to F0-10(Max frequency)
Accelerate/Decelerate curve	Line or S-curve Acc/Dec mode, four kinds of Acc/Dec time Range of Acc/Dec Time0.0~65000.00s.
DC brake	DC brake frequency: 0.00Hz to Maximum frequency brake time: 0.0 to 36.0s brake current value: 0.0 to 100%
Simple PLC, Multi-speed	16-speed operating through built-in PLC or control terminal
Built-in PID	Close loop control system can be formed easily by using PID
Automatic voltage regulating (AVR)	Output voltage is regulated when voltage of the power network changes
Overvoltage and over current stall control	During operation automatically limits the inverter output current and bus voltage, to prevent fan over current and overvoltage trip.
Rapid current limiting function	Minimizing flow failures, protect the normal operation of the inverter
Instantaneous stop non-stop	Load feedback energy compensation voltage is reduced and continues to maintain a short time when change is momentarily interrupted.
Speed tracking start	For high-speed rotation of the motor speed identification, impact- free smooth start
Rapid current limit	Rapid software and hardware limiting technology to avoid frequent converter over current fault.
Virtual IO	Five sets of virtual DO, five sets of virtual DI, enables easy logic control.
Timing Control	Timing control: set the time range 0.0Min~6500.0Hour
Multi-motor switch	Two independent motor parameters, enabling two motors switching control
Bus Support	Two independent Modbus communication, CAN-Link
Command source	Given the control panel, control terminal, serial communication port given. It can be switched by a variety of ways.
Torque boost	Auto Torque boost Manual Torque boost ; 0.1%~30.0%.
Frequency source	Nine kinds of frequency sources: digital setting, analog voltage setting, analog current setting, pulse setting, or serial port and so on. It can be switched by a variety of ways.
Auxiliary frequency source	Nine kinds of auxiliary frequency source. Flexible implementation of auxiliary frequency tuning, frequency synthesis.
Input terminal	Six digital input terminals, one only supports 50khz high pulse input Two analog input terminals, one support 0V~10V voltage input One support 0 ~ 10V voltage input or 0 ~ 20mA current input
Output terminal	One high-speed pulse output terminal (optional open collector type), support of square wave 0 ~ 50kHz signal output One digital output terminal One relay output terminals Two analog output terminals, support 0 ~ 20mA current output or 0 ~ 10V voltage output
Display and operation
LED display		Display parameters and status information
The key lock and function selection		Achieve some or all of the keys locked, scope definition section keys to prevent misuse.
Protection function		Input/output phase failure protection ,Overcurrent protection ;Over voltage protection; Undervoltage protection; Overheat protection ; Overload protection
Options		Brake assembly, PG card
Environment
Application environment		In-door, free from direct sunlight, dust , corrosive gas, combustible gas, oil mist , steam , water drop and salt .
Altitude		Lower than 1000m
Vibration		Less than 5.9m/s(0.6g)

Technical characteristics

High precision of steady speed:0.5%(open loop vector control)0.02%(close loop vector control), It can completely meet the high precision requirement of CNC machine.
Large torque at low frequency: compare with other brands, higher mechanical function, stronger feed capacity, and cutting depth, it can improve the efficiency of machine tools and production capacity.

Fast response: faster acceleration/deceleration time, up to 0.1 seconds, improve the efficiency of machine tool production.
Built-in DC brake, and external braking resistor, can reach to start-stop at high speed stably and reliably.

Wiring diagram:

Factory tour:

Product Tags:

dc motor matlab model

dc stepper motor controller

elctronic speed controller

Inquiry Cart 0