CHIFON ELECTRIC CO.,LIMITED
BEST SERVICE, WE DRIVE!
Add to Cart
FPR500A High-performance Asynchronous Motor Inverter
►Power class
Single-phase 220v±15% 0.4-2.2kw
Three-phase 380V±15% 0.75-315kw
►Product introduction
FPR500 series relies on TI company's DSP dual-core professional control motor chip, which supplies the international leading vector control algorithm to realize the real high-precision flux vector torque control. It has built-in pg vector control (VC), pg-free vector control (SVC), and V/F control modes, which are widely applied to high-speed control accuracy, rapid torque response, and high performance at low frequency. The integration of torque control, speed control, and position control can meet the high-performance requirements of customer applications. And, FPR 500 has the ability to exceed the anti-trip performance of similar products and adapt to the severe power grid, ambient temperature, humidity, and dust, greatly improving the reliability of products.
Certificates
►Products Specifications:
| Basic Function | Specification | |
| Maximum output frequency | 0~500Hz | |
| Carrier frequency | 0.5kHz~16.0kHz;According to the load characteristics, carrier frequency can be adjusted automatically | |
| Input frequency | Range :47~63Hz | |
| Control mode | V/F Open/closed loop vector control(SVC/FVC) | |
| Speed range | 1:50(Vector mode 0 ) 1Hz/150% rated torque | |
| Overload capability | G type:150% rated current for 60s; 180% rated current for 3s P type:120% rated current for 60s; 150% rated current for 3s | |
| Torque boost | Auto Torque boost Manual Torque boost; 0.1%~30.0%. | |
| V/F curve V/F | Four modes : Line , Multi-point , Square V/F curve, V/F separation | |
| Jog control | Jog frequency range:0.00Hz to F0-10(Max frequency) | |
| Accelerate/Decelerate curve | Line or S-curve Acc/Dec mode, four kinds of Acc/Dec time Range of Acc/Dec Time0.0~65000.00s. | |
| DC brake | DC brake frequency: 0.00Hz to Maximum frequency brake time: 0.0 to 36.0s brake current value: 0.0 to 100% | |
| Simple PLC, Multi-speed | 16-speed operating through built-in PLC or control terminal | |
| Built-in PID | Close loop control system can be formed easily by using PID | |
| Automatic voltage regulating (AVR) | Output voltage is regulated when voltage of the power network changes | |
| Overvoltage and over current stall control | During operation automatically limits the inverter output current and bus voltage, to prevent fan over current and overvoltage trip. | |
| Rapid current limiting function | Minimizing flow failures, protect the normal operation of the inverter | |
| Instantaneous stop non-stop | Load feedback energy compensation voltage is reduced and continues to maintain a short time when change is momentarily interrupted. | |
| Speed tracking start | For high-speed rotation of the motor speed identification, impact- free smooth start | |
| Rapid current limit | Rapid software and hardware limiting technology to avoid frequent converter over current fault. | |
| Virtual IO | Five sets of virtual DO, five sets of virtual DI, enables easy logic control. | |
| Timing Control | Timing control: set the time range 0.0Min~6500.0Hour | |
| Multi-motor switch | Two independent motor parameters, enabling two motors switching control | |
| Bus Support | Two independent Modbus communication, CAN-Link | |
| Command source | Given the control panel, control terminal, serial communication port given. It can be switched by a variety of ways. | |
| Torque boost | Auto Torque boost Manual Torque boost ; 0.1%~30.0%. | |
| Frequency source | Nine kinds of frequency sources: digital setting, analog voltage setting, analog current setting, pulse setting, or serial port and so on. It can be switched by a variety of ways. | |
| Auxiliary frequency source | Nine kinds of auxiliary frequency source. Flexible implementation of auxiliary frequency tuning, frequency synthesis. | |
| Input terminal | Six digital input terminals, one only supports 50khz high pulse input Two analog input terminals, one support 0V~10V voltage input One support 0 ~ 10V voltage input or 0 ~ 20mA current input | |
| Output terminal | One high-speed pulse output terminal (optional open collector type), support of square wave 0 ~ 50kHz signal output One digital output terminal One relay output terminals Two analog output terminals, support 0 ~ 20mA current output or 0 ~ 10V voltage output | |
| Display and operation | ||
| LED display | Display parameters and status information | |
| The key lock and function selection | Achieve some or all of the keys locked, scope definition section keys to prevent misuse. | |
| Protection function | Input/output phase failure protection ,Overcurrent protection ;Over voltage protection; Undervoltage protection; Overheat protection ; Overload protection | |
| Options | Brake assembly, PG card | |
| Environment | ||
| Application environment | In-door, free from direct sunlight, dust , corrosive gas, combustible gas, oil mist , steam , water drop and salt . | |
| Altitude | Lower than 1000m | |
| Vibration | Less than 5.9m/s(0.6g) | |
►FAQ:
What is a variable frequency drive?
A VFD is used to control the speed of an AC induction motor. it can do this by varying the motors supplied voltage and changing the frequency of the power. Three major designs are used in VFD they are pulse width modulation, current source inverter, and voltage source inverter
It has become the most common drive controller it is because a VFD works very well with motor ranging, it is highly reliable, affordable, and it only reflects the least amount of harmonics back to the power source.
Fault conditions in VFD (motor fault analysis)
Troubleshooting VFDs
If you have an unidentified wide frequency band vibration fault it is possible that it is a VFD problem. It can be corrected by additional tuning of torque profiles, carrier frequencies, or smoothing parameters may correct the issue